National Instruments PCI-DIO-96 DAQ Parallel Digital I/O Interface Card

Description

National Instruments PCI-DIO-96 DAQ Parallel Digital I/O Interface Card
Comes with what you see in the pictures. If you don't see it, you probably wont get it.
Specifications are from National Instruments and may vary slightly due to upgrades, options, or revisions this unit may or may not have.
This card is used and guaranteed to work.
The Unit's Serial Number Tag Reads:
Model Number:
PCI-DIO-96
Part Number:
182920K-01
Serial Number:
133B527
CE Marked:
Yes
Key Features:
Unidirectional and bidirectional I/O
Known power-up state
2-wire handshake capability
NI-DAQmx driver simplifiers configuration and measurements
Description:
The PCI-DIO-96 uses four 24-bit programmable peripheral interfaces (PPIs). You can divide each PPI into three eight-bit ports. The PCI-DIO-96 is flexible for interfacing to peripherals or other computers. It can operate in either a unidirectional or bidirectional mode and handshake with peripheral equipment.
Digital I/O Specifications:
Number of Channels:
96 I/O
Compatibility:
TTL
Power On State:
Inputs (high-Z), pulled up through 100 kΩ
Handshaking:
Input, output, or bidirectional
Data Transfers:
Interrupts, programmed I/O
Digital Logic Levels Specifications:
Input Signals:
The maximum input logic high and output logic high voltages assume a V
cc
supply voltage of 5.0 V. Given a V
cc
supply voltage of 5.0 V, the absolute maximum voltage rating for each I/O line is -0.5 V to 5.5 V with respect to GND.
Level:
Min.:
Max.:
Input Logic High Voltage:
2.2 V
5.3 V
Input Logic Low Voltage:
-0.3 V
0.8 V
Input High Current:
(V
in
= 5 V, resistors set to pull-up
1
)
-
10 µA
2
Input High Current:
(V
in
= 5 V, resistors set to pull-down
1
)
-
75 µA
Input Logic Low Current:
(V
in
= 0 V, resistors set to pull-up
1
)
-
-75 µA
Input Logic Low Current:
(V
in
= 0 V, resistors set to pull-down
1
)
-
-10 µA
2
1:
The PCI-DIO-96 bias resistors are always set to pull-up.
2:
Exception: Lines PC3 and PC0 are 20 µA.
Output Signals:
Pin 49 (at +5 V):
1.0 A max.
Level:
Min.:
Max.:
Output Logic High Voltage (I
ol
= -2.5 mA):
3.0 V
5.0 V
Output Logic High Voltage (I
oh
= -4 mA):
2.7 V
5.0 V
Output Logic Low Voltage (I
oh
= 2.5 mA)
0 V
0.4 V
Output Logic Low Voltage (I
ol
= 4 mA
0
0.5 V
Output Current:
2.5 mA typ.
Transfer Rates Specifications:
Max with NI-DAQ Software:
50 kbytes/s
Constant Sustainable Rate (Typ.):
1 to 10 kbytes/s
Note:
Transfer rates are a function of the speed with which your program reads data from or writes data to the board, and therefore vary with your system, sfotware, and application.
Bus Interface Specifications:
Type:
Slave
Power Requirement Specifications:
Power Consumption:
400 mA at +5 VDC (±5%)
Power Available at I/O Connector:
+4.65 to +5.25 V fused at 1 A
Physical Specifications:
Dimensions:
13.7 cm x 10.7 cm (5.4" x 2.4")
Weight:
101 g (3.6 oz)
I/O Connector:
100-pin female 0.050 series D-type
Environment Specifications:
Operating Temperature:
0°C to 55°C
Storage Temperature:
-20°C to 70°C
Relative Humidity:
5% to 90%, noncondensing
Maximum Altitude:
2,000 meters
Pollution Degree:
2
For Domestic Customers: Packaging, handling, and order processing included in shipping in all domestic shipments as quoted by the shipping calculator. For International Customers there is a {{detail_product_description}}.00 minimum for packaging, handling, and order processing. International shipping to be determined by destination.
Prior to shipment I will need to know the following information (filled out on a form that I will send you) for International Customers or Packages/Freight being Forwarded internationally. International customers may also be subject to a freight forwarder form if applicable.:
(1) Are you the end-user of this item?
(2) If you are not the ultimate end-user of the item, please state the ultimate end user's name.
(3) What is the ultimate country destination?
02/27/17